168+ Shed Roof On Back Of House

www.dwell.com

```html

DIY Shed Roof Extension: Adding Protection and Value to Your Home

Are you looking to extend your outdoor living space and protect your back door or patio from the elements? Building a shed roof extension onto your house is a fantastic DIY project that can significantly enhance your property. This step-by-step guide will walk you through the process, ensuring a successful and rewarding outcome.

Planning and Preparation

Before you even think about picking up a hammer, careful planning is crucial. This stage involves assessing your needs, obtaining necessary permits, and gathering the right tools and materials.

Step 1: Assess Your Needs and Design Consider the desired size and purpose of your shed roof extension. How much space do you need covered? What is the desired aesthetic? Sketch out a basic design, taking into account the slope of the roof and how it will integrate with your existing house structure.

Step 2: Check Local Building Codes and Obtain Permits This is non-negotiable. Contact your local building department to determine if permits are required for your project. Failure to obtain permits can result in fines or even forced removal of the structure.

Step 3: Gather Tools and Materials Creating a comprehensive list beforehand saves time and frustration. Essential tools include:

• Measuring tape
• Level
• Circular saw
• Drill/driver
• Hammer
• Safety glasses
• Gloves
• Pencil
• Ladder
• Chop Saw (Optional, but recommended for cleaner cuts)

Materials will vary based on your design, but typically include:

• Lumber (pressure-treated for ground contact) for posts, beams, rafters, and sheathing
• Roofing materials (shingles, metal roofing, etc.)
• Flashing
• Fasteners (nails, screws, bolts)
• Concrete (for post footings)
• Post anchors (if not setting posts directly in concrete)

Building the Frame

The frame is the skeleton of your shed roof extension. Accuracy and proper construction are critical for stability and longevity.

Step 4: Install Posts Dig holes for your support posts, ensuring they are deep enough to meet local building codes (typically below the frost line). Set the posts in concrete, ensuring they are plumb (perfectly vertical). Allow the concrete to cure completely before proceeding. If using post anchors, attach them to the concrete footings according to the manufacturer's instructions.

Step 5: Attach the Ledger Board to the House The ledger board is a crucial component that attaches the roof extension to your house. It must be securely fastened to the existing structure. Use lag bolts to attach the ledger board to the house framing, making sure to locate the wall studs or rim joist. Proper flashing is essential to prevent water damage. Install flashing above the ledger board, overlapping the existing siding and extending down over the top of the ledger board.

Step 6: Install Beams Attach the beams to the tops of the support posts. These beams will support the rafters. Ensure they are level and securely fastened using appropriate hardware.

Step 7: Install Rafters Cut the rafters to the desired length and angle. Attach the rafters to the ledger board and the beam, ensuring they are evenly spaced. Use rafter ties to secure the rafters to the ledger board and the beam for added strength.

Roofing and Finishing

With the frame in place, it's time to add the sheathing and roofing materials to protect your extension from the elements.

Step 8: Install Sheathing Cover the rafters with sheathing (plywood or OSB). Ensure the sheathing is properly secured with nails or screws. Leave a small gap between sheets to allow for expansion and contraction.

Step 9: Install Roofing Underlayment Apply roofing underlayment (felt paper or synthetic underlayment) over the sheathing. This provides an extra layer of protection against water damage. Overlap the underlayment according to the manufacturer's instructions.

Step 10: Install Roofing Materials Install your chosen roofing material (shingles, metal roofing, etc.) according to the manufacturer's instructions. Pay close attention to proper overlap and fastening techniques to ensure a watertight seal.

Step 11: Install Flashing Install flashing around any penetrations in the roof, such as chimneys or vents. Also, install flashing along the edges of the roof where it meets the house.

Step 12: Finishing Touches Add any desired finishing touches, such as trim, gutters, and downspouts. Paint or stain the wood to protect it from the elements and enhance its appearance.

Conclusion

You Might Also Like: 171 Contemporary Shed Roof House Plans

Congratulations! You've successfully built a shed roof extension onto your house. This project not only adds valuable covered space but also enhances the overall value and appeal of your home. Remember to regularly inspect and maintain your new structure to ensure its longevity and continued performance. Enjoy your new outdoor space!

```

Photo 1 Of 6 In Modern Shed Roof House By Jonathan Ball

www.dwell.com

Photo 4 Of 6 In Modern Shed Roof House By Jonathan Ball

www.dwell.com

Hidden Bend Retreat, Romney West Virginia: Shed Roof On Back Of House Dried In

martinloghouse.blogspot.com